3 Genius Ways to Raise Your Office Chair Without Lever Easily

May 24, 2022

29 Views

While you can always find the perfect office chair for your use, adjustments are crucial for it. How to raise an office chair without a lever?

People sit for long hours in an office chair. Height adjustment is a key factor to enhance comfort. FittingChairs will guide you how to raise office chair without lever.

How To Choose The Correct Height?

When looking to purchase a new chair or how to raise office chair without lever, one of the most important aspects you need to consider is the seating height it provides.

Office chairs often equipped with a gas stem often have quite a wide height variable. Not only that, the standard height options will be able to accommodate most people’s requirements.

However, if you are uncertain, it’s always best to measure beforehand.

Source: Plan n Design

Whether finding out how to raise office chair without lever is that possible? Traditional ergonomics concepts will tell you.

A seat height that ranges from about 16 to 21 inches off the floor should work for most people.

This height will allow the user to have his or her feet flat on the floor, with thighs horizontal and arms even with the height of the desk.

You know, an optimum height for an office chair will put your knees into a 90-degree angle. Let’s check with your feet.

If your feet are resting on the floor, that also means that the seat height must be able to reach the back of your knees.

With a pneumatic adjustment lever, you can adjust easily. But, how to raise office chair without lever if you feel it is too low compared to your demand?

Can We Raise An Office Chair Without A Lever?

In fact, it is not very simple on how to raise office chair without lever, but you can do it.

Source: MacSources

By what? You can use bolt movements or also move in clockwise movements to adjust the height.

How To Raise Office Chair Without Lever?

Using Wooden Pieces

Instead of using a lever, you can use pieces of wood for how to raise office chair without lever to reach a few inches.

It is highly recommended to use a 2×2 inch piece for a better grip.

Detach The Seat

To do it, you will have to place the pieces in between the seat and the lower part of the chair. After that, you will have to use a drill and make a hole in the wooden piece.

Then you have to pass long screws and nuts through those holes. The number of woods depends upon the number of screws in the chair.

After adjusting them, you have to attach the seat back and reattach it. Just doing this small step can help you raise the chair to a few inches.

Source: Carousell

You know, it’s still hard on how to raise office chair without lever. Of course, this method will require a little more effort and energy.

If you find it too difficult to remove and rebind the screws tightly, it is recommended to take help of a professional if you doubt it.

Through Threaded Post

If you need to raise your chair a little more, you may have to check if your chair has a threaded post for height adjustment. For that, you need to lubricate the chair upside down.

Don’t forget that the dirt of your office chair also stands in the way of adjusting the chair’s height with a threaded post. Keep your clothes clean.

Then, just secure the chair’s base with your feet to prevent it from moving right or left and move it in an anticlockwise direction to increase its height.

Turning it clockwise clockwise direction is a good way if you want to lower the height. Continue turning it until you reach your desired height.

Compared to a lot of ways, this is relatively easy but for executing this.

But, your chair must have a threaded post. If it does not have that, you will have to use wooden pieces to raise it to an approximate height.

Source: Workaroundtc

Of course, if your chair has a lever, that’s always great.

How To Adjust The Height Of An Old Non-Pneumatic Office Chair?

Frankly speaking, adjusting the height of an old non-pneumatic chair isn’t as simple as using a lever.

In some difficult cases like these older office chairs have threaded posts, you will need to turn the chair clockwise or counterclockwise to adjust the height.

Here are some steps on how to raise office chair without lever for old non-pneumatic chair:

Step 1

The first step is to identify the height you will need to adjust your office chair to.

Source: To Ergonomic

Ideally, like you find out above, you can determine that the adjustable height should be equal to the distance between the floor and the middle of your knee joint.

So, measure the distance from the floor to the middle of your knee joint while standing up. After that, continue to measure the distance from the floor to the seat of your chair.

Take note of the difference to perform the pre-steps exactly on how to raise office chair without lever.

Step 2

Most of these old chairs often have a small lock that prevents you from accidentally readjusting the height. Find it.

You might need to flip your chair over to locate this lock and unfasten it.

Keep in mind that it is usually a small screw. Of course, it’s not in the open. You can find at the base of the chair you will need to loosen it with a screwdriver.

Step 3

After you loosen its lock, start to flip the chair back to its normal position and begin adjusting the height.

Turn the chair clockwise for applying how to lower office chair without lever and counterclockwise to raise it.

Don’t forget to keep a foot at the base of the chair to prevent the base from turning with the seat. One full turn of the seat raises or lowers it by approximately ¼ inch.

Use the measurements you took on step one to determine how many full turns you will need to get the right height.

Source: The Human Solution

Test it by sitting on the chair before reinserting the lock.

Step 4

Once your ergonomic office chair has the perfect height, reinsert the lock and tighten it.

Reinsert the lock. In this step, you don’t need to flip the chair over again to avoid messing up your height adjustment.

How To Fix A Broken Lever?

If you want to know how to raise office chair with lever, think of how to fix the broken lever.

Below are step by step to fix:

Step 1. Tip the recliner forward until the arms and the back of the recliner rest on the floor.

Step 2. Look along the bottom of the recliner lever for the set screw and use a torx screwdriver to remove the set screw.

Step 3. Pull the broken lever from the side of the recliner and the escutcheon from beneath the broken lever.

Step 4. Slide the new escutcheon provided with the new lever over the recliner mechanism on the side of the recliner.

Step 5. Use the torx-head set screw, provided with the replacement lever, to secure the lever to the recliner.

Step 6. Return the recliner to an upright position.

Source: Rainy Day Magazine

How To Lock Office Chair Height?

Here are steps to lock your office chair height:

Step 1. Sit all the way in the chair with your feet on the ground.
Step 2. Push the height adjustment lever backward to move the chair up and down.
Step 3. Stand up off the chair slightly to reduce the pressure of the chair as you push the lever.
Step 4. Find the correct position and push the lever forward to lock it into position.

See more:

Adjusting an office chair without a lever is different. In this article of FittingChairs, you have learned some easy steps on how to raise office chair with lever. The better you adjust it, the more comfortable you will sit on your chair.